|
 |
|
|
|
|
|
|
Format |
ToolMod Module Size 2U |
|
|
Versions |
TM107-20h - +/- 20 dB, horizontal Face Plate
TM107-20v - +/- 20 dB, vertical Face Plate
TM107-12h - +/- 12 dB, horizontal Face Plate
TM107-12v - +/- 12 dB, vertical Face Plate |
|
|
Power Supply |
Tool-Series Standard |
|
|
Supply Voltages |
+/- 25 V and + 48 V Phantom |
|
|
Supply Current *) |
+/- 100 mA |
|
|
|
|
|
Input |
electronically balanced |
|
|
nominal Level |
+ 6 dBu - Gain |
|
|
maximum Level |
> + 30 dBu - Gain |
|
|
Input Impedance |
40 Hz - 15 kHz > 10 kOhms |
|
|
nominal Source Impedance |
50 Ohms |
|
|
CMRR |
15 kHz > 65 dB, typical 75 dB 1 kHz > 80 dB, 40 Hz > 90 dB |
|
|
|
|
|
Output |
electronically balanced |
|
|
nominal Level |
+ 6 dBu |
|
|
maximum Level |
> + 30 dBu |
|
|
Source Impedance |
50 Ohms, see Diagram
Output Source Resistance vs Frequency |
|
|
Load Resistor |
see Diagram
maximum Output Level vs Load Resistor
and
maximum Output Level vs capacitive Load |
|
|
CMRR according to IEC |
> 40 dB, siehe Diagram Output CMRR vs Frequency |
|
|
|
|
|
Gain |
0 dB +/- 0.3 dB linear setting |
|
|
|
|
|
Frequency Response
|
20 Hz - 30 kHz +/- 0.75 dB linear setting |
|
|
Bandwidth |
< 10 Hz to > 150 kHz |
|
|
|
|
|
Phase Response |
20 Hz-20 kHz < +6/-10° linear setting
- see Diagram Phase Response
|
|
|
|
|
|
THD |
< + 28 dBu, 40 Hz ... 20 kHz, < 0.1 %,
maximum THD at + 30 dBu <1 % |
|
|
|
|
|
Dynamic Range / Noise |
|
|
|
RMS 22Hz-22kHz |
<= -91 dBu linear setting |
|
|
total Dynamic Range |
referring to the RMS Value 22Hz-22kHz
>= 121 dB linear setting |
|
|
|
|
|
High EQ |
active RC-Filter with Shelving Characteristics
with Frequency Control from 1 kHz to 40 kHz
and Steepness 6 dB/Oct. - 12 dB/Oct., selected by switch
Control Range +/- 20 dB or +/- 12 dB,depending on Version
|
|
|
Low EQ |
active Vienna Bridge Filter
Bell Characteristics with Center Frequency Control
15 Hz to 400 Hz +/- 15 %
and Q-Factor Q = 0.5 and Q = 2, selected by switch
Control Range +/- 20 dB or +/- 12 dB, depending on Version
|
|
|
Mid EQ |
fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 100 Hz +/- 10 % to 10 kHz, +/- 15 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 20 dB or +/- 12 dB, depending on Version
|
|
|
|
|
|
Bypass Circuitry |
Hardbypass by Relay |
|
|
|
|
|
*) The standard supply current is the supply current under realitic operation conditions. If the outputs are loaded with the minium load resistors and the level is at + 30 dBu, the supply current increases by 30 mA per output. The standard supply current shuold be used to calculate the necessary power supply capacity of a system. |
|
|
|
|
|
|
|
|