Technical Specifications ToolMod TM215 Stereo Peak Limiter |
|||
|
|||
Format | ToolMod Module Size 2U | ||
Versions | TM215h - horizontal Face Plate TM215v - vertical Face Plate |
||
Power Supply | Tool-Series Standard | ||
Supply Voltages | +/- 25 V and + 48 V Phantom | ||
Supply Current *) | +/- 200 mA | ||
Input | electronically balanced, Stereo | ||
nominal Level | + 6 dBu - Gain | ||
maximum Level | > + 30 dBu - Gain | ||
Input Impedance | 40 Hz - 15 kHz > 10 kOhms | ||
nominal Source Impedance | 50 Ohms | ||
CMRR | 15 kHz > 65 dB, typical 75 dB 1 kHz > 80 dB, 40 Hz > 90 dB | ||
Output | electronically balanced, Stereo | ||
nominal Level | + 6 dBu | ||
maximum Level | > + 30 dBu | ||
Source Impedance | 50 Ohms, see Diagram Output Source Resistance vs Frequency |
||
Load Resistor | see Diagram maximum Output Level vs Load Resistor and maximum Output Level vs capacitive Load |
||
CMRR according to IEC | > 40 dB, siehe Diagram Output CMRR vs Frequency | ||
Gain | 0 dB +/- 0.3 dB at Gain in Mittelstellung Control Range +/- 10 dB +/- 1 dB der Gain Regler bestimmt den Outputspegel hinter Limiter |
||
Frequency Response |
20 Hz - 50 kHz +/- 0.2 dB no Regulation - see Diagram Frequency Response |
||
Bandwidth | < 10 Hz to > 150 kHz | ||
Phase Response | 20 Hz-20 kHz < +6/-10° linear setting - see Diagram Phase Response |
||
THD | < + 28 dBu, 40 Hz ... 20 kHz, < 0.1 %, maximum THD at + 30 dBu <1 % no Regulation THD under regulation is determined by the frequency, attack and release settings, and the gain reduction |
||
Crosstalk | > 70 dB, 40 Hz ... 15 kHz | ||
Dynamic Range / Noise | |||
RMS 22Hz-22kHz | <= -92 dBu no Regulation at 0 dB Gain | ||
total Dynamic Range | referring to the RMS Value 22Hz-22kHz >= 122 dB no Regulation at 0 dB Gain |
||
Control Voltage Rejection |
> 70 dB | ||
Limiter | very fast Peak Limiter | ||
Threshold | Control Range + 20 dB to - 10 dB, referring to + 6 dBu 0 dB Setting internally calibrated |
||
Attack | Attack Time Adjustment for 10 dB Attenuation Control Range 0.02 ms to 7 ms (with short attack time, the period of the input signal determines the real attack time) |
||
Release | Release Time Adjustment for 10 dB Gain Change Control Range 50 ms to 3 s |
||
Gain | Output gain post limiter with calibrated
center click @ 0 dB and +/- 10 dB range |
||
Display | Gain reduction display with 5 LED's, display range from 1 dB to 10 dB |
||
Bypass Circuitry | Hardbypass by Relay | ||
*) The standard supply current is the supply current under realitic operation conditions. If the outputs are loaded with the minium load resistors and the level is at + 30 dBu, the supply current increases by 30 mA per output. The standard supply current shuold be used to calculate the necessary power supply capacity of a system. | |||